Transcription

REWHITE MOTORSSERIESThe RE Series motors offer the perfect compromise between price and performance by producingworkhorse power at a reasonable cost. Although these motors perform well in a wide range ofapplications, they are especially suited for low flow, high-pressure applications. During startup,pressure causes the balance plate to flex toward the rotor, vastly improving volumetric efficiency.As the motor reaches operating pressure, the balance plate relaxes, allowing the rotor to turnfreely, which translates into higher mechanical efficiencies. Transmitting this power to the outputshaft is the most durable drive link in its class. Three bearing options, combined with standardmounting flanges and output shafts, allow the motor to be configured to suit nearly any application.FeaturesHeavy-Duty Drive Link is most durable in its class and receives full flow lubrication to provide longlife.Valve-In-Rotor Design provides cost effective, efficient distribution of oil and reduces overallmotor length.Pressure-Compensated Balance Plate improves volumetric efficiency at low flows and highpressure.Three Bearing Options allow load carrying capability of motor to be matched to application.High Pressure Viton Shaft Seal offers superior seal life and performance and eliminates needfor case drain.Displacementin 3/rev(cm3/rev)Max SpeedRPM Cont. Code07101214161820242632457.4 (121)9.9 (162)12.4 (204)14.2 (232)15.9 (261)18.3 (300)21.2 (348)22.8 (375)28.3 (465)32.7 (536)45.6 (748) 360 370 300 260 260 250 220 200 160 140 100 Max FlowGPM (LPM)Inter.490470370320350320270250200170130CROSS HYDRAULICS PTY LTD Cont. Inter.12 (45) 16 (61) 18 (68) 18 (68) 20 (76) 22 (83) 22 (83) 20 (76) 20 (76) 20 (76) 20 (76) 16 (61)20 (76)22 (83)22 (83)24 (91)25 (95)25 (95)24 (91)24 (91)24 (91)24 (91)Max Torquelb-in (Nm) Cont. 2900 (327) 4200 (473) 4800 (540) 5700 (642) 6300 (709) 7300 (822) 8150 (918) 8900 (1002) 9650 (1076) 8700 (980) 9400 (1028) Inter. *Stall3400 (383) 4800 (540) 5600 (631) 6300 (709) 7000 (788) 8300 (935) 9250 (1042) 10250 (1154) 10475 (1179) 11000 (1239) 10950 (1233) 2240 (253)3100 (350)4200 (475)4905 (554)5345 (604)6095 (689)6290 (711)7600 (859)8040 (909)7260 (820)7905 (893) Pressure PSI( --Bar)Cont. Inter. Peak 3000 (207) 3000 (207) 3000 (207) 3000 (207) 3000 (207) 3000 (207) 3000 (207) 3000 (207) 2500 (172) 2000 (138) 1500 (103) 3500 (241) 3500 (241) 3500 (241) 3500 (241) 3500 (241) 3500 (241) 3500 (241) 3500 (241) 2750 (189) 2500 (172) 1750 (121) 4000 (276)4000 (276)4000 (276)4000 (276)4000 (276)4000 (276)4000 (276)4000 (276)3000 (207)3000 (207)2000 (138)GREEN CATALOGUE Page 8.01

REWHITE MOTORSSERIES120 7.4 in. 3/r (121cc)Areas within white representmaximum motor efficiencies.160 9.9 in. 3/r (162cc)Note: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDTorque, lb-in (Nm)Speed, RPMNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.02

REWHITE MOTORSSERIES200 12.4 in. 3/r (204cc)Areas within white representmaximum motor efficiencies.230 14.2 in. 3/r (232cc)Note: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDTorque, lb-in (Nm)Speed, RPMNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.03

REWHITE MOTORSSERIES260 15.9 in. 3/r (261cc)Areas within white representmaximum motor efficiencies.300 18.3 in. 3/r (300cc)Note: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDTorque, lb-in (Nm)Speed, RPMNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.04

REWHITE MOTORSSERIES350 21.2 in. 3/r (348cc)Areas within white representmaximum motor efficiencies.375 22.8 in. 3/r (375cc)Note: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDTorque, lb-in (Nm)Speed, RPMNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.05

REWHITE MOTORSSERIES470 28.3 in. 3/r (465cc)Areas within white representmaximum motor efficiencies.540 32.7 in. 3/r (536c)Note: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDTorque, lb-in (Nm)Speed, RPMNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.06

REWHITE MOTORSSERIES750 45.6 in. 3/r (748cc)Areas within white representmaximum motor efficiencies.Torque, lb-in (Nm)Speed, RPMNote: Max Flow and Max Pressuremust not occur simultaneously.CROSS HYDRAULICS PTY LTDNote: Performance data is typical.Performance of production unitsvaries slightly from one motor toanother.GREEN CATALOGUE Page 8.07

REWHITE MOTORSSERIESHOUSINGSA31 4-Hole Front Aligned Ports 7/8 O-RingA38 4-Hole Front Aligned Ports 1/2 BSP.F2.80 (71) Max22.5oSAE ‘A’ FlangeDim J2.39 (61)2.58 (66) Max.70 (18) Max2.47 (63) Min.120 (3.0).110 (2.8)B5.38 (137) Max3.250 (82.6)3.247 (82.5).90 (23)4.99 (127).90 (23)AO 4.187 (106.3).522 (13.3).514 (13.1)Optional Relief Cartridge shown installedand is available for both A31 and A38housings.12 (3).06 (2)Seal Groove DetailDim J2.52 (64).91 (23)2.35 (60) Min1.24 (31) DiaSpotface4.21(107)Dim J is on page 8.10Valve Cavity - 10 Series/2-way (7/8-14 UNF-2B)A51 6-Hole Front Aligned Ports 7/8 O-RingA58 6-Hole Front Aligned Ports 1/2 BSP.FDim J2.80 (71) Max2.58 (66) Max22.5o2.47 (63) Min2.39 (61).70 (18) Max.120 (3.0).110 (2.8)3.250 (82.6)3.247 (82.5)O 4.187 (106.3).522 (13.3).514 (13.1)CROSS HYDRAULICS PTY LTD.12 (3).90 (23)4.99 (127).90 (23)Seal Groove Detail.06 (2)GREEN CATALOGUE Page 8.08

REWHITE MOTORSSERIESHOUSINGSWheel MountW31 4-Hole Front Aligned Ports 7/8 O-RingW38 4-Hole Front Aligned Ports 1/2 BSP.F1.745 (44.3)1.741 (44.2)5.21 (132) Max.524 (13.3).514 (13.1)Dim K1.45 (37).76 (19)2.47 (63) Min.10 (3) Min.20 (5)B3.23 (82)5.45 (138) Max3.250 (82.6)3.247 (82.5).90 (23)4.999 (127.0)4.995 (126.9).90 (23)A45oO 5.812 (147.6)Optional Relief Cartridge shown installed and isavailable for both W31 and W38 housings.Dim K.72 (18)1.14 (29)2.25 (57)1.24 (31) Dia.Spotface4.13 (105)Valve Cavity - 10 Series/2-way (7/8-14 UNF-2B)Dim K is on page 8.10CROSS HYDRAULICS PTY LTDGREEN CATALOGUE Page 8.09

REWHITE MOTORSSERIESTechnicalAllowable Bearing And Shaft LoadingBearing Curve: The bearing curve represents allowable bearing loads based on ISO281 bearing capacity for an L10 life of 2000 hours at 100 RPM. Radial loads for speedother than 100 RPM may be calculated using the multiplication factor table below.Shaft Curve: The shaft curve represents a 3:1 safety factor based on a tensilestrength of 330 kpsi.A Style Flange-100 -75-50-250255075100mm9,0008,0003,5001,000 lbs445 DaN7,000mm4,0003,0001,000 lbs445 5in.Wheel Mount-75-50-259,0008,000mm4,0003,5001,000 lbs445 DaN7,0003,0001,000 lbs445 000Bearing500DaN1,000lbs.-3-2-10CROSS HYDRAULICS PTY LTD12345in.Length and WeightTablesA Style FlangeDisp.CodeDim. Jin (mm)Weightlbs (kg)1201602002302603003503754705407506.37 (162)6.37 (162)6.51 (165)6.61 (168)6.70 (170)6.83 (174)7.38 (187)7.08 (180)7.38 (187)7.62 (194)8.33 (212)23.4 (10,6)23.4 (10,9)24.2 (11,0)24.4 (11,1)25.0 (11,3)25.8 (11,7)28.2 (12,8)27.0 (12,2)28.2 (12,8)29.4 (13,3)32.5 (14,7)RE motor weights vary /- 1 lb. (.45 kg)depending upon motor configuration.Wheel MountDisp.CodeDim. Kin (mm)Weightlbs (kg)1201602002302603003503754705407504.72 (120)4.72 (120)4.86 (123)4.95 (126)5.05 (128)5.18 (132)5.73 (146)5.43 (138)5.73 (146)5.97 (152)6.68 (170)25.8 (11,7)25.8 (11,7)26.6 (12,1)26.8 (12,2)27.4 (12,4)28.2 (12,8)30.6 (13,9)29.4 (13,3)30.6 (13,9)31.8 (14,4)34.9 (15,8)RE motor weights vary /- 1 lb. (.45 kg)depending upon motor configuration.Bearing Load MultiplicationFactor TableRPM Multiplication 0.587000.568000.50GREEN CATALOGUE Page 8.10

REWHITE MOTORSSERIESShaftsMax. Torque: 5,880lb-in660 Nm10 1 Inch StraightMountingFlangeDim L1.59(40).251 (6.4).250 (6.4)1.020 (25.9).970 (24.6).70 (18)Min.251 (6.4).250 (6.4).314 (8).313 (8).394 (10.0).392 (9.9).32 (8)1.250 (31.8)1.249 (31.7)5/8-18 UNF.314 (8.0).313 (8.0).276 (7.0).274 (7.0)1.33 (34)Wire Ring021.37 (35).20 (5).957 (24.3).907 (23.0).17 (4)1.00-20 UNEF15o1:8 Taper?Dim L.83 (21)MountingFlange1.60 (41)Min Spline1.249 (31.7)1.245 (31.6)14 Tooth 12/24 PitchStd. ANSI B92.1-1996Spline5/8-18 UNFCROSS HYDRAULICS PTY LTD20o?Max. Torque:10,600 lb-in1,200 NmDim L1.00 (25)Min. SplineMountingFlange1.59 (40).70 (18)Min.245 (6.2).243 (6.1)O .810(20.6)1.00-6B Spline(SAE J499 Std)Max. Torque: 10,600lb-in1,200 Nm1.90 (48)1.33 (34)(Wire Ring).06 (2) DiaWire Ring.996 (25.3).992 (25.2)Note: A slotted nut is standard on this shaft.23 14 Tooth Spline.46 (12)6-B Spline1.250 (31.8)1.248 (31.7).15 (4)1.285 (32.6)1.235 (31.4)1.260 (32.0)1.259 (31.9)MountingFlangeDim L.75 (19).63 (16)MinM8 x 1.25o15Max. ?Torque: 10,600lb-in1,200 Nm?22 1-1/4 Inch Tapered1.90 (48).276 (7.0).274 (7.0)1.372 (34.8)1.359 (34.5).06 (2)?Dia?Wire RingMountingFlangeDim L2.14 (54).83 (21)Min1.33 (34)Wire RingMax. Torque: 10,600lb-in1,200 Nm21 32mm Straight1.90 (48)1.388 (35.3)1.376 (35.0)30oMountingFlangeDim L2.14 (54).276 (7.0).274 (7.0).984 (25).983 (25)30oMax. ?Torque: 10,600lb-in1,200 Nm20 1-1/4 Inch Straight1.168 (29.7)1.218 (30.9).212 (5.4)M8 x 1.255/16-18 UNCMountingFlange.63 (16)Min.2766 (7).2756 (7)1.08 ?(27.4)1.07 ?(27.2).999 (25.4).998 (25.3).314 (8.0).313 (8.0)Dim L1.83(46.5).18 (5)1.110 (28.2)1.101 (28.0)Max. Torque: 5,617lb-in635 Nm25mm Straight12.06 (2) DiaWire Ring15o5/16-18 UNC30oShaft LengthsDim LShaftCode02222023102112"A" Style Flangein (mm)1.97 (50)2.58 (66)2.41 (61)2.42 (61)1.97 (50)2.41 (61)2.21 (56)Wheel Mountin (mm)3.60 (91)4.22 (107)4.05 (103)4.06 (103)3.60 (91)4.05 (103)3.84 (98)Shaft lengths vary /- .030 in. (.8mm)GREEN CATALOGUE Page 8.11

REWHITE MOTORSSERIES500Rotation Selection501BABABABAFor applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the A portof the motor. To obtain the desired direction of shaft rotation, usethe graphic at the left to determine the rotation code for the motor. For bidirectional applications, the 500 series is recommended.Preferred rotation direction is determined by the internal valvingdesign.Ordering InformationSERIES501500REVERSED TIMINGDISPLACEMENT HOUSINGCodeDisplacement1207.4 in3/r160121 cc9.9 in3/r162 cc20012.4 in3/r204 cc23014.2 in3/r232 cc26030015.9 in3/r261 cc18.3 in3/r300 -Hole FrontPorts 1/2" BSP.F026-B SplineONo OptionsA384-Hole Front Ports1/2" BSP.F (S)221-1/4" TaperedFFree TurnW31 4-Hole Front Ports7/8" O-ring4-Hole Front PortsA317/8" O-ring (S)6-Hole Front PortsA517/8" O-ring201-1/4" Straight2314 Tooth Spline101" Straight1225mm Straight2132mm StraightA586-Hole Front Ports1/2" BSP.FJDeclutchXSolid NutPLock Nut*RRelief Valve Cavity*R11000 PSI(69 Bar) ReliefValve Installed*R22000 PSI(138 Bar) Relief ValveInstalled35021.2 in3/r348 cc37522.8 in3/r375 cc*R347028.3 in3/r465 cc3000 PSI(207 Bar) Relief ValveInstalled**Z50 Pulse Sensorw/4pin Connector54032.7 in3/r536 cc**Z175045.6 in3/r748 cc50 Pulse Sensor w/Male(tower) Hsg. WeatherPack Connector**Z230 Pulse Sensorw/4pin Connector**Z330 Pulse Sensor w/Male(tower) Hsg. WeatherPack Connector**Z430 Pulse Sensorw/Female (shroud) Hsg.Weather Pack Connector**Z5100 Pulse Sensorw/4pin Connector**Z6100 Pulse Sensorw/Male (tower) Hsg.Weather Pack Connector*Available with A31, A38, W31, andW38 housings**Available with A31 and A38 housingsand must use a medium duty shaft(see page 18 for order codes(S) Speed sensor componentsCROSS HYDRAULICS PTY LTDGREEN CATALOGUE Page 8.12