Transcription

Cybex Arc Trainer 630AOwner’s ManualCardiovascular SystemsPart Number 5630A-4www.cybexinternational.com

Cybex Arc Trainer 630AOwner’s ManualCardiovascular SystemsPart Number 5630A-4Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Polar is a registered trademark of Polar .DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. Wereserve the right to revise this document at any time or to make changes to the product described within it without notice orobligation to notify any person of such revisions or changes. 2006 Cybex International, Inc. All rights reserved. Printed in United States of America.10 Trotter Drive Medway, MA 02053 800-766-3211 508-533-4300 FAX 508-533-5183www.cybexinternational.com [email protected] [email protected] 5630A-4 Rev A September 2006

Cybex Arc Trainer 630A Owner’s ManualAbout This ManualAn Owner’s Manual is shipped with each unit. To purchase additional copies of this manual orany other Cybex manual, please do one of the following: order online at www.cybexinternational.comfax your order to 508-533-5183contact Cybex Customer Service at 800-766-3211or contact Cybex Customer Service at 508-533-4300To contact Cybex with comments about this manual you may send email [email protected] Compliance Information! WARNING: Changes or modifications to this unit not expressly approved by the partyresponsible for compliance could void the user’s authority to operate theequipment.This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there isno guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception (which can be determined byturning the equipment off and on) the user is encouraged to try to correct the interference byone or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. Consult the dealer or an experienced radio TV technician for help.Page i

Cybex Arc Trainer 630A Owner’s ManualDECLARATION OF CONFORMITYThis Declaration of Conformity is suitable to the European Standard EN 45014, “General criteria forsupplier’s declaration of conformity.”We,Manufacturer: Cybex International, Inc.EU Representative:10 Trotter DriveMedway, MA 02053USA(508) 533-4300Cybex International UKOaktree HouseAtherstone RoadMeashamSwadlincote, Derbyshire DE12 7ELUnited Kingdom 44 (0)845 60 60 228declare under our sole responsibility that the product(s):Cybex 620A Arc TrainerCybex 629A Arc TrainerCybex 630A Arc TrainerCybex 639A Arc Trainerto which this declaration relates is in conformity with the EEC directives listed herein below(including any and all relevant modifications):73/23/EECLow Voltage Directive89/336/EECElectromagnetic Compatibility93/42/EECMedical Device DirectiveEd KurzontkowskiSenior Vice President - Manufacturing Operations and Customer ServiceCybex International, Inc.10 Trotter DriveMedway, MA 02053507-455-0217 x 250Page iiWorldwide Headquarters 10 Trotter Drive Medway, MA 02053, USA t 508.533.4300 f 508.533.5500151 24th Avenue NW Owatonna, MN 55060, USA t 507.455.0217 f 507.455.3446

Cybex Arc Trainer 630A Owner’s ManualAs a result of test reports and their evaluation by accredited laboratories, we are in possession of thefollowing certificates for products which carry this marking:Canada, USAWorldwideEuropean UnionCAN/CSA-C22.2 No.601.1-M90UL Std. No. 60601-1 MedicalFCC Part 15, Subpart B Class BEN 55011, Group 1, Class BEN 60601-1-2CB SchemeIEC60601-173/23/EEC, 89/336/EEC,93/42/EECReferences of harmonized standards on which this declaration of conformity is based:EN 60601-1-1 Medical electrical equipment - Part 1-1: General requirements for safety - Collateralstandard: Safety requirements for medical electrical systemsEN 60601-1-2 Medical electrical equipment - Part 1-2: General requirements for safety - Collateralstandard: Electromagnetic compatibility - Requirements and testsEN 61000-4-2 (1995) Electromagnetic compatibility (EMC): Testing and measurement techniques Electrostatic discharge immunity testEN 61000-4-3 (1996) Electromagnetic compatibility (EMC): Testing and measurement techniques Radiated, radio-frequency, electromagnetic field immunity testEN 61000-4-4 (1995) Electromagnetic compatibility (EMC): Testing and measurement techniques Section 4: Electrical fast transient/burst immunity test.EN 61000-4-5 (1995) Electromagnetic compatibility (EMC): Testing and measurement techniques Surge immunity testEN 61000-4-6 (1996) Electromagnetic compatibility (EMC): Testing and measurement techniques Immunity to conducted disturbances, induced by radio-frequency fieldsWorldwide Headquarters 10 Trotter Drive Medway, MA 02053, USA t 508.533.4300 f 508.533.5500151 24th Avenue NW Owatonna, MN 55060, USA t 507.455.0217 f 507.455.3446Page iii

Cybex Arc Trainer 630A Owner’s ManualEN 61000-4-8 (1993) Electromagnetic compatibility (EMC): Testing and measurement techniques Power frequency magnetic field immunity testEN 61000-4-11 (1994) Electromagnetic compatibility (EMC): Testing and measurement techniques Voltage dips, short interruptions and voltage variations immunity testsEN 61000-3-2 (2000) Electromagnetic compatibility (EMC): Limits - Limits for harmonic currentemissions (equipment input current 16A per phase)EN 61000-3-3 (1995/1997) Electromagnetic compatibility (EMC): Limits - Limitation of voltagechanges, voltage fluctuations and flicker in public low-voltage supply systems, for equipment withrated current 16 A per phase and not subject to conditional connectionEN 957-1 Stationary Training Equipment. General Safety Requirements and Test MethodsEN 957-9 Stationary training equipment – Elliptical trainers. Additional specific safety requirementsand test methods.FCC Part 15, Subpart B – Class B EmissionsCAN/CSA-C22.2 No. 601.1-M90 – Medical Electrical Equipment – Part 1: General Requirements forSafetyUL-60601-1 Medical Electrical Equipment, Part 1: General Requirements for SafetyASTM F1749-96 Standard Specification for Fitness Equipment and Fitness Facility Safety Signageand LabelsPage ivWorldwide Headquarters 10 Trotter Drive Medway, MA 02053, USA t 508.533.4300 f 508.533.5500151 24th Avenue NW Owatonna, MN 55060, USA t 507.455.0217 f 507.455.3446

Cybex Arc Trainer 630A Owner’s ManualTable of ContentsFront PagesAbout this Manual . . . . . . . . . . . . . . . . . .FCC Compliance Information . . . . . . . . .Declaration of Conformity . . . . . . . . . . . .Table of Contents . . . . . . . . . . . . . . . . . .1 SafetyImportant Voltage Information . . . . . . . . .Grounding Instructions. . . . . . . . . . . . . . .Important Safety Instructions . . . . . . . . .Warning Decals . . . . . . . . . . . . . . . . . . . .Warning Decals For Units with ACPower Kit . . . . . . . . . . . . . . . . . . . . . . . .Caution Decals . . . . . . . . . . . . . . . . . . . .Explanation of Symbols Used . . . . . . . . .iiiiv1-11-11-21-51-71-81-92 Technical SpecificationsSpecifications . . . . . . . . . . . . . . . . . . . . . 2-13 OperationTerms and Symbols Used . . . . . . . . . . . .Intended Use . . . . . . . . . . . . . . . . . . . . . .Quick Operation Guide . . . . . . . . . . . . . .Detailed Operation Guide . . . . . . . . . . . .Stopping the Arc Trainer 630A . . . . . . . .Control During Operation . . . . . . . . . . . .Data Readouts . . . . . . . . . . . . . . . . . . . . .Displaying Heart Rate . . . . . . . . . . . . . . .Heart Rate LED . . . . . . . . . . . . . . . . . . . .Use of Programs . . . . . . . . . . . . . . . . . . .Manual Mode. . . . . . . . . . . . . . . . . . . . . .The Workout Profile . . . . . . . . . . . . . . . . .Range of Motion . . . . . . . . . . . . . . . . . . .Hill Interval . . . . . . . . . . . . . . . . . . . . . . . .Interval . . . . . . . . . . . . . . . . . . . . . . . . . . .Weight Loss . . . . . . . . . . . . . . . . . . . . . . .Cardio . . . . . . . . . . . . . . . . . . . . . . . . . . .Strength . . . . . . . . . . . . . . . . . . . . . . . . . .Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 43-163-183-203-224 Preventive MaintenanceWarnings . . . . . . . . . . . . . . . . . . . . . . . . .Regular Maintenance Activities . . . . . . . .Cleaning Your Arc Trainer 630A . . . . . . .Drive Belt Maintenance . . . . . . . . . . . . . .Lubrication . . . . . . . . . . . . . . . . . . . . . . . .Environment . . . . . . . . . . . . . . . . . . . . . . .Storage . . . . . . . . . . . . . . . . . . . . . . . . . .Service Schedule . . . . . . . . . . . . . . . . . . .Rechargeable Battery . . . . . . . . . . . . . . .4-14-14-24-34-54-54-54-64-75 Setup and AssemblyWarnings/Cautions . . . . . . . . . . . . . . . . .Choosing and Preparing a Site . . . . . . . .Electrical Power Requirements . . . . . . . .Assembling the Arc Trainer 630A . . . . . .Testing the Operation . . . . . . . . . . . . . . .Setting Operation Options. . . . . . . . . . . .5-15-15-25-25-115-126 Customer ServiceContacting Service . . . . . . . . . . . . . . . . .Serial Number and Voltage . . . . . . . . . . .Return Material Authorization (RMA) . . . .Damaged Parts . . . . . . . . . . . . . . . . . . . .Ordering Parts . . . . . . . . . . . . . . . . . . . . .PartList - Main Assembly. . . . . . . . . . . . .Exploded View - Main Assembly. . . . . . .Exploded View - Main Assembly. . . . . . .Parts List - Console Assembly . . . . . . . .Exploded View - Console Assembly . . . .Parts List - Front End Assembly . . . . . . .Exploded View - Front End Assembly . . .Schematic . . . . . . . . . . . . . . . . . . . . . . . .6-16-16-26-36-36-46-56-66-86-96-106-116-13Page v

Cybex Arc Trainer 630A Owner’s Manual1 - SafetyIMPORTANT:Read all instructions and warnings before using the unit.Important Voltage InformationNOTE: The power cord is available with the optional AC power kit.! WARNING: Do not plug unit into wall outlet without an approved medical power cord.Before plugging the power cord into an electrical outlet, verify that the voltage requirements for yourarea match the voltage of the unit that you have received.Grounding InstructionsThis unit must be grounded. If it should malfunction or break down, grounding provides a path of leastresistance for electric current to reduce the risk of electric shock. This product is equipped with a cordhaving an equipment-grounding conductor and a grounding plug. The plug must be plugged into anappropriate outlet that is properly installed and grounded in accordance with all local codes andordinances.! DANGER: Improper connection of theequipment grounding conductor can result in arisk of electric shock. Check with a qualifiedelectrician or service provider if you are in doubtas to whether the unit is properly grounded. Seeka qualified electrician to perform anymodifications to the cord or plug. Cybex is notresponsible for injuries or damages as a result ofcord or plug modification.Make sure that the unit is connected to an outlethaving the same configuration as the plug. Do notuse a ground plug adapter to adapt the power cordto a non-grounded outlet.115VNEMA 5-15Euro PlugCEE 7/7SafetyPage 1-1

Cybex Arc Trainer 630A Owner’s ManualImportant Safety Instructions(Save These Instructions)! DANGER: To reduce the risk of electric shock, always unplug this unit from the electrical outletimmediately after using it and before cleaning it.! WARNING: Serious injury could occur if these precautions are not observed. To reduce the riskof burns, fires, electric shock, or injury:User Safety PrecautionsSafetyPage 1-2 Keep children away. Teenagers and disabled must be supervised.Tenez les enfants éloignés. Lesadolescents et les handicapés doivent être surveilles. Obtain instruction before using. Lisez les instructions avant l'utilisation. Wait until foot plates come to a complete stop before dismounting. Attendre l'arret complet desreposes pieds avant de descendre. Obtain a medical exam before beginning any exercise program. Stop exercising if you feel faint, dizzy, or experience pain. Read and understand the Owner's Manual and all warnings posted on the unit before using. DO NOT wear loose or dangling clothing while using. Keep all body parts, towels, and the like free and clear of moving parts. Use the handrails for support and to maintain balance. DO NOT use the unit if you exceed 400 lbs. (180 kg). This is the rated maximum user weight. Replace any warning labels if damaged, worn or illegible. Report any malfunctions, damage or repairs to the facility. Wait until foot plates come to a complete stop before dismounting. All maintenance activities shall be performed by qualified personnel. Failure to do so could result inserious injury. DISCONNECT POWER BEFORE SERVICING. Moving parts. Keep hands away when in use. For connection to a Medical Grade outlet only to ensure proper grounding. Rated 100-240 VAC 50/60 Hz 0.75 A.

Cybex Arc Trainer 630A Owner’s ManualFacility Safety Precautions Make sure all user and safety precautions are observed. Read and understand the Owner's Manual completely before using the unit. Make sure all users are properly trained on how to use the equipment. Make sure that each machine is setup and operated on a solid level surface. Do not installequipment on an uneven surface. Make sure there is enough room for safe access and operation of the equipment. Perform regular maintenance checks on the equipment. Also pay close attention to all areas mostsusceptible to wear, including (but not limited to) cables, pulleys, belts and grips. Immediately replace worn or damaged components. If unable to immediately replace worn ordamaged components then remove from service until the repair is made. Do not attempt repairs, electrical or mechanical. Seek qualified repair personnel when servicing. Ifyou live in the USA, contact Cybex Customer Service at 800-766-3211. If you live outside the USA,contact Cybex Customer Service at 508-533-4300. Disconnect the optional power adapter before servicing the unit. Keep a repair log of all maintenance activities. Use only Cybex supplied components to maintain/repair the equipment. Do not use attachments unless recommended for the unit by Cybex. Do not use the unit if: the unit is plugged into an optional power adapter that has a damagedcord; (2) the unit is not working properly or (3) if the unit has been dropped or damaged. Seekservice from a qualified technician. Do not use the optional power adapter in damp or wet locations. EQUIPMENT not suitable for use in the presence of a FLAMMABLE ANAESTHETIC MIXTURE WITHAIR or WITH OXYGEN OR NITROUS OXIDE. Do not use the unit outdoors. The 630A may generate electromagnetic or other forms of interference, or it may be affected byinterference from other equipment nearby. If this is suspected, take precautions by separating theequipment or otherwise shielding it to avoid such interference.NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regularmaintenance is performed.Arc Trainers containing the A/V options Devices connected to Cybex equipment must comply with appropriate safety standards. Thisincludes but not limited to: (UL-60601, IEC/EN 60601-1) for medical equipment. There must be adequate mechanical mounting of the device in all combinations(configurations).SafetyPage 1-3

Cybex Arc Trainer 630A Owner’s ManualSafetyPage 1-4 The device must be stable on the unit in all configurations. Risk and leakage current of the final combinations must comply with IEC/EN 60601-1-1 and is theresponsibility of the end user to ensure compliance. Electromagnetic emissions and immunity of all configurations must conform to IEC/EN 60601-1-2. All added devices must have a compatible interface. All devices must be used for their intended purpose. Signal or mains isolation devices and additional protective earth may be needed to assurecompliance with IEC/EN 60601-1-1. Do not power the entire system from a single outlet or power strip. If the unit is used with theoptional power supply, ensure that this power supply is plugged in to a separate outlet than anyconnected device, to prevent exceeding the allowable leakage current of the system. End user of a system shall ensure that interruption and restoration of the power supply to anyequipment or non-medical equipment of the system shall not result in a safety hazard other thaninterruption or cessation of its intended function.

Cybex Arc Trainer 630A Owner’s ManualWarning DecalsCarefully read and understand the following before using the unit:NOTE: To replace any worn or damaged decals do one of the following: Visitwww.cybexinternational.com to shop for parts online, fax your order to 508-533-5183 or contact CybexCustomer Service at 800-766-3211. If you live outside of the USA, call 508-533-4300.Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death orserious injury. The warning decals are shown below.Warning decal part number610A-349-4WARNINGKeep children away. Teenagers anddisabled must be supervised.Tenezles enfants éloignés. Lesadolescents et les handicapésdoivent être surveilles.Obtain instruction before using.Lisez les instructions avantl'utilisation.SERIOUS INJURYCOULD OCCUR IFTHESE PRECAUTIONSARE NOT OBSERVEDWait until foot plates come to acomplete stop before dismounting.Attendre l'arret complet desreposes pieds avant de descendre.Obtain a medical exam beforebeginning any exercise program.Stop exercising if you feel faint,dizzy, or experience pain.Read and understand the Owner'sManual and all warnings posted onthe unit before using.DO NOT wear loose or danglingclothing while using.Keep all body parts, towels, and thelike free and clear of moving parts.Use the handrails for support andto maintain balance.DO NOT use the unit if you exceed400 lbs. (180 kg). This is the ratedmaximum user weight.Replace any warning labels ifdamaged, worn or illegible.Report any malfunctions, damageor repairs to the facility. 610A-349-4SafetyPage 1-5

Cybex Arc Trainer 630A Owner’s ManualUnderneathAccess CoverWarning decal part number - DE-19592-4Shield part number630A-316SERIOUS INJURY COULD OCCURIF THESE PRECAUTIONSARE NOT OBSERVEDHigh voltage is present underthis shield. This shield shouldonly be removed by a qualifiedservice technician.Keep wet items away frominside parts.High voltage may still be presenteven if the unit is unplugged.Warning batteryDE-19586Located onbattery bracketWarning decal part numberDE-17155-4WARNINGHot flywheel! Wait until itcools before servicing.DE-17155-4SafetyPage 1-6

Cybex Arc Trainer 630A Owner’s ManualWarning Decals for Units with AC Power KitWarning decal part numberCM000240CM000240Warning decal part numberDE-19547-4WARNINGFor connection to a Medical Gradeoutlet only to ensure proper grounding.WARNINGGraden to a MedicalFor connectiogrounding.ensure properoutlet only to50/60HzVAC Voltage: 100-240DE-19547-4Voltage: 100-240 VAC 50/60Hz0.75 Amps1-PhaseDE-19547-4SafetyPage 1-7

Cybex Arc Trainer 630A Owner’s ManualCaution DecalsCaution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor ormoderate injury. The caution decals are shown below.CAUTIONMoving parts.Keep hands awaywhen in use.DE-17219-4Caut