Transcription

Cybex Arc Trainer 750A/750ATOwner’s ManualCardiovascular SystemsPart Number 5750-4 Dwww.cybexinternational.com

Cybex Arc Trainer 750A/750ATOwner’s ManualCardiovascular SystemsPart Number 5750-4 DCybex and the Cybex logo are registered trademarks of Cybex International, Inc.Polar is a registered trademark of Polar Electro Inc.iPOD is a registered trademark of Apple Inc.DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We reservethe right to revise this document at any time or to make changes to the product described within it without notice or obligation to notifyany person of such revisions or changes. 2009, Cybex International, Inc. All rights reserved. Printed in United States of America.10 Trotter Drive Medway, MA 02053 888-462-9239 508-533-4300 FAX 508-533-5183www.cybexinternational.com [email protected] 5750-4 D November 2009

Cybex Arc Trainer 750A/750AT Owner’s ManualTable of ContentsFront PagesAbout this Manual . . . . . . . . . . . . . . . . . . . iiiFCC Compliance Information . . . . . . . . . iii1 SafetyGrounding and Voltage Information . . . .Important Safety Instructions . . . . . . . . . .Warning and Caution Decals . . . . . . . . . .CSAFE Ports.1-11-21-41-72 Assembly and SetupWarning and Caution . . . . . . . . . . . . . . . .Choosing and Preparing a Site . . . . . . . .Electrical Power Requirements . . . . . . . .Unit Assembly . . . . . . . . . . . . . . . . . . . . . .Testing Operation . . . . . . . . . . . . . . . . . . .Setup Screen . . . . . . . . . . . . . . . . . . . . . .2-12-12-12-22-152-163 OperationIntended Use . . . . . . . . . . . . . . . . . . . . . .Terms Used . . . . . . . . . . . . . . . . . . . . . . . .Mount and Dismount . . . . . . . . . . . . . . . .Emergency Dismount . . . . . . . . . . . . . . . .Range of Motion . . . . . . . . . . . . . . . . . . . .Console Keys . . . . . . . . . . . . . . . . . . . . . .Audio Visual (AV) Key Pad - Optional . .Program Selection . . . . . . . . . . . . . . . . . .Programs P1 – P9 Setup . . . . . . . . . . . . .Manual and Quick Start Program Setup .Advanced Programs A1 – A2 Setup . . . .Custom Programs . . . . . . . . . . . . . . . . . . .Data Readouts . . . . . . . . . . . . . . . . . . . . .Heart Rate Indicator . . . . . . . . . . . . . . . . .Fan Control . . . . . . . . . . . . . . . . . . . . . . . .Alarm Set . . . . . . . . . . . . . . . . . . . . . . . . . .Battery Sentry . . . . . . . . . . . . . . . . . . . . . 3-123-124 Preventive MaintenanceWarnings . . . . . . . . . . . . . . . . . . . . . . . . . .Cleaning Unit . . . . . . . . . . . . . . . . . . . . . . .Preventive Maintenance Activities . . . . . .Remove Access Cover . . . . . . . . . . . . . . .Attach Access Cover . . . . . . . . . . . . . . . .Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . .Recommended Service Schedule . . . . . .Statistics . . . . . . . . . . . . . . . . . . . . . . . . . .Error Codes . . . . . . . . . . . . . . . . . . . . . . . .Rechargeable Battery . . . . . . . . . . . . . . .Environment . . . . . . . . . . . . . . . . . . . . . . .4-14-14-24-24-24-34-34-44-54-64-65 Customer ServiceContacting Service . . . . . . . . . . . . . . . . . .Serial Number . . . . . . . . . . . . . . . . . . . . . .Ordering Parts . . . . . . . . . . . . . . . . . . . . . .Servicing Double-Insulated Products . . .Damaged Parts . . . . . . . . . . . . . . . . . . . . .Return Material Authorization (RMA) . . .5-15-15-25-25-35-3Appendix A–Technical Specifications . . . A-1Appendix B–Program Overviews . . . . . . . . B-1Appendix C–Parts Lists. . . . . . . . . . . . . . . . . C-1Appendix D–Exploded Views . . . . . . . . . . . D-1Appendix E–Schematics . . . . . . . . . . . . . . . E-1Page i

Cybex Arc Trainer 750A/750AT Owner’s ManualAbout This ManualAn owner’s manual is shipped with each unit. To purchase additional copies of this manual orany other Cybex manual, see Chapter 5 – Customer Service for Cybex contact information.To contact Cybex with comments about this manual, email [email protected] Compliance InformationWARNING: Changes or modifications to this unit not expressly approved by theparty responsible for compliance could void the user’s authority tooperate the equipment!This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and (if not installedand used in accordance with the instructions) may cause harmful interference to radiocommunications. There is no guarantee that interference will not occur in a particularinstallation.If equipment does cause harmful interference to radio or television reception,(determine byturning the equipment off and on) the user is encouraged to try to correct the interference byone or more of the following methods: Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a different circuit from the receiver.Consult dealer or an experienced radio/TV technician.Page iii

Cybex 750A/750AT Arc Trainer Owner’s Manual1 – SafetyIMPORTANT: Read all instructions and warnings before using.Grounding and Voltage InformationDANGER: Improper connection of equipment grounding conductor can result in a risk of electricshock. Check with a qualified electrician or service provider if in doubt as to whether theunit is properly grounded.For Optional Power SupplyUnit must be grounded. This unit is equipped with an optional equipment-grounding conductor cordand a grounding plug.Do not use a ground plug adapter to adapt the power cord to a non-grounded outlet.Plug must be plugged into an appropriate outlet that is properly installed and grounded in accordancewith all local codes and ordinances.If unit malfunctions, grounding provides path of least resistance for electric current to reduce risk ofelectric shock.Cybex is not responsible for injuries or damages as a result of cord or plug modification.Verify voltage requirements of unit match local voltage requirements.Verify unit outlet is the same configuration as the plug.Power Adapter24 VDCPower CordConnectorVaries byCountryNOTE: Use Cybex supplied power adapter and power cords only.SafetyPage 1-1

Cybex 750A/750AT Arc Trainer Owner’s ManualImportant Safety Instructions(Save These Instructions)DANGER: To reduce the risk of electrical shock, always unplug unit from electrical outlet immediatelyafter use and before cleaning.WARNING: Serious injury could occur if these listed precautions are not observed. Followprecautions to reduce the risk of burns, fires, electric shock or injury.User Safety PrecautionsObtain medical exam before beginning any exercise program.WARNING: Heart rate monitoring systems may be inaccurate. Over exercise may result in seriousinjury or death. If you feel faint stop exercising immediately.Stop exercising if feeling faint, dizzy or experiencing pain and consult your physician.Obtain instruction before using. Lisez les instructions avant l’utilisation.Read and understand the Owner’s Manual and all warnings posted on the unit before using.Keep children away. Teenagers and disabled must be supervised. Tenez les enfants éloignés. Lesadolescents et les handicapés doevent être surveilles.Use the handrails for support and to maintain balance.Wait until foot plates come to a complete stop before dismounting. Attendre l’arret complet desreposes pieds avant de descendre.Keep foot plate surface clean and dry.DO NOT wear loose or dangling clothing while using.Keep all body parts and other items free and clear of moving parts.DO NOT use unit if user weight exceeds 400 lbs (180 kg). This is the rated maximum userweight.Report any malfunctions, damage or repairs to the facility.Replace any warning labels if damaged, worn or illegible.SafetyPage 1-2

Cybex 750A/750AT Arc Trainer Owner’s ManualFacility Safety PrecautionsNOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance isperformed.Enforce all user and safety precautions.Read and understand the Owner’s Manual completely before assembling, servicing or using unit.Verify all users are properly trained on using the equipment.Do not use unit outdoors.Verify that each unit is setup, leveled and operated on a solid, level surface. Do not install equipmenton an uneven surface.Verify there is enough room for safe access and operation of unit.Use Cybex AC power adapters only.Do not use the optional power adapter in damp or wet locations.Do not use the unit if: (1) the unit is plugged into an optional power adapter that has a damaged cord;(2) the unit is not working properly or (3) if the unit has been dropped or damaged. Seek service froma qualified technician.EQUIPMENT is not suitable for use in the presence of aerosol (spray), FLAMMABLE ANAESTHETICMIXTURE WITH AIR or WITH OXYGEN or NITROUS OXIDE.Perform regular maintenance checks on unit. Performance level can be maintained only if examinedregularly. Pay close attention to all areas most susceptible to wear, including (but not limited to)cables, pulleys, belts and grips.Replace any warning labels if damaged, worn or illegible.Immediately replace worn or damaged components. If unable to immediately replace worn ordamaged components, then remove unit from service until repair is made.Do not attempt repairs; electrical or mechanical. Seek qualified repair technician when servicing.Failure to do so could result in serious injury. See Chapter 5 – Customer Service for contactinformation.Use only Cybex supplied components to maintain/repair unit.Keep a repair log of all maintenance activities.Disconnect the optional power adapter before servicing unit.Do not use attachments unless recommended for the unit by Cybex.The unit may generate electromagnetic or other forms of interference, or it may be affected byinterference from other equipment nearby. If this is suspected, take precautions by separating theequipment or otherwise shielding it to avoid such interference.SafetyPage 1-3

Cybex 750A/750AT Arc Trainer Owner’s ManualUnit with A/V OptionsDevices connected to Cybex equipment must comply with appropriate safety standards. This includesbut not limited to: UL 1647 and EN 60335-1.There must be adequate mechanical mounting of the device in all combinations (configurations).Device must be stable on the unit in all configurations.Warning and Caution DecalsNOTE: To replace any worn or damaged labels, see Chapter 5 – Customer Service for contact information.Warning decals indicate a potentially hazardous situation which, if not avoided, could result in deathor serious injury.Carefully read and understand the following caution and warning labels before using the unit.Warning decal part number750A-372-4 (if applicable)WARNINGDISCONNECT POWERBEFORE SERVICING.Voltage: 100-240 VAC 50/60Hz 1.8 Amps 1-Phase750A-372-4 ASafetyPage 1-4

Cybex 750A/750AT Arc Trainer Owner’s ManualWARNINGSERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED1. Obtain a medical exam before beginning any exercise program.4. Obtain instruction before using. Lisez les instructions avant l'utilisation.10. DO NOT wear loose or dangling clothing while using.2. WARNING! Heart rate monitoring systems may be inaccurate.Over exercise may result in serious injury or death. If you feelfaint stop exercising immediately.5. Read and understand the Owner's Manual and all warningsposted on the unit before using.11. Keep all body parts and other items free and clear of moving parts.3. Stop exercising if feeling faint, dizzy, or experiencing pain andconsult your physician.6. Keep children away. Teenagers and disabled must be supervised.Tenez les enfants éloignés. Les adolescents et les handicapésdoivent être surveilles.7. Use the handrails for support and to maintain balance.12. DO NOT use unit if user exceeds 400 lbs. (180 kg). This is the ratedmaximum user weight.13. Report any malfunctions, damage or repairs to the facility.14. Replace any warning labels if damaged, worn or illegible.750A-330-48. Wait until foot plates come to a complete stop before dismounting.Attendre l'arret complet des reposes pieds avant de descendre.9. Keep foot plate surface clean and dry.Warning decal partnumber 750A-330-4Warning decal part numberDE-17219-4 (Both Sides)CAUTIONMoving parts.Keep hands awaywhen in use.DE-17219-4 ASafetyPage 1-5

Cybex 750A/750AT Arc Trainer Owner’s ManualWarning decal part numberDE-17155-4WARNINGHot flywheel! Wait until itcools before servicing.DE-17155-4 ANOTE: Decal on inside of igh erOver-Te dching og triggere speed and Low powB,G,I,K8Approa y watchd arity - Low speed andA,B,C,Glh9Displa d irregu arity - Higl22Spee d irregu too slowly k stoppedg23Spee ine movin nt feedbacn.redatioory Erro24Incl ine moveme dalifi .rmclor Memqu injuryablesMinfo25IndiROby usineting- EEPed26Incl Battery tureoogeredrm serio27Low Tempera chdog trigrfole shR) R)verpe lt inub28O oller watTEbe resutlet.d troEN ENTEall29Contr0,surell outaileR)sh uldcloco7,5, 8,8,TE. m waR.r deEn nsities souleTEAR AR 8, 9, ENl fotived serviceit frouaake/ ectioac to do9 EN(CLE (CLE9,9,cen Br nnManSch endedplug un9,9, TERupeaARan ilureCoictRicervSe nost (CLEEA s ENA.Cl eck Fuse ryvice mm t, unntenl. FaSetos CL. Presmai nerSer recower KiB.Ch eck BatteDiag isticsferwe V)ntAll rsonpresPoC.Ch ecknrreimum PoStatn, ETER: Repeit.tio e Cu rnal ( 12wnar.TEmin l ACun tdow M .D.ChtegeNOusthe tionaigna akling un ODOanced weenes 6 - Br 2V Exy Volta otor DoUpanis is g op e. t peda itial co m is distMDnionD LED - 1 spla n M otorite edin: Th in ag arar.LEioMtensTE If us ile 1.St ring enu mulatiddeD 7 Diticmford weNO TE: ine mLE D 8 - Elevat ationgHosltsan th. - u2.Due first accuNO termbegnLE D 9 - - Elevpion rnea sideterinTh viewrnDia itEnDetens de an inLE D 10drivewotoED3unsmforeckAN ICKL EaceLEancleKmltsumus4plChive0be cu r toe Tr ce StatTR ARGDs80d reive d va veLEnsol e Re ges/atus orCH3y anileKm k dr an ss coHOM- Co nsol Char ge St eratmbl400 Chec e unit acce0MFR HIG GEar GenD 1 Co ry80asseet 50 AARUSLE D 2 - Batte ry Ch ms/MovmovATionCHfroFirs3MileLE D 3 - Batte redRe Km elevatY ST E E0040PR GLE D 4 - PowekER50 A00TTAR32 CheceryLE D 5 L5BABCHD36Evs/3LEC MileNOERY4,000TTC23D220 DBA3eryK14EvC24 RNINGAll maintenance activities shall be performed by qualifiedpersonnel. Failure to do so could result in serious injury.Warning decal part number - 750A-329-4SafetyPage 1-6

Cybex 750A/750AT Arc Trainer Owner’s ManualCSAFE PortThe CSAFE standard defines a communication protocol and low-voltage DC power source specific to theFitness Equipment Industry. These RJ-45 phone jacks are provided for use ONLY within the CSAFE protocol.For more information on CSAFE standard, visit www.fitlinxx.com/csafe.NOTE: The CSAFE port inside the console, accessible through the back cover, is the only port that carriesBOTH the CSAFE communication lines and the 8.0v DC CSAFE power supply. If attaching a CSAFEcompliant device that requires power, this connection must be used. Power is present only when theunit is in use or when a power supply is attached.Back of ConsoleCSAFE Port (J9)Communication8V DC/100 MAPower SupplyJ7J9J10J8J5SafetyPage 1-7

Cybex 750A/750AT Arc Trainer Owner’s ManualThis page intentionally left blank.SafetyPage 1-8

Cybex Arc Trainer 750A/750AT Owner’s Manual2 – Assembly and Set UpWarning and CautionRead and understand all warnings and cautions listed in Chapter 1 – Safety before assembling unit.Use extreme caution when assembling the unit. Failure to do so could result in injury or death.WARNING: Always use proper lifting methods when moving heavy items.Ensure all electrical requirements are met as indicated in the specifications in Chapter 1 – Safety and aslisted in this chapter.Choosing and Preparing SiteBefore assembling the unit, verify chosen site meets the following criteria:Area is well lit and well ventilated.Surface is structurally sound and properly leveled. NOTE: Place a 3/4” (1.9 cm) thick wood base underunit to protect carpeting.Area allows for ample access and passage clearance around unit or for emergency dismount. Minimumclearance is 19.7 inches (.5 meters) on at least one side of unit and also behind unit.NOTE: The access and passage clearance dimensions stated are the recommended minimum dimensionsas set forth by the manufacturer. The actual area for access and passage is the responsibility of thefacility and should take into account any required local codes or regulations.Area is not in vicinity of high humidity, such as in the vicinity of a steam room, sauna, indoor pool oroutdoors. This unit is designed to function normally in an environment with a relative humidity range of30% to 75%.NOTE: Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics aswell as other parts of the unit.Area maintains an ambient temperature range of 50 F (10 C) to 104 (40 C).Electrical Power RequirementsNOTE: The AC power kit is optional.Verify unit is connected to an outlet having the same configuration as the plug.Verify connection is a grounded circuit. NOTE: Do not use a ground-plug adapter to adapt the 3-prong powercord to a non-grounded electrical outlet.NOTE: Use Cybex supplied optional AC power kit only. Consult an electrician with any questions.Verify power supply is compliant with local building codes.Assembly and Set UpPage 2-1

Cybex Arc Trainer 750A/750AT Owner’s ManualUnit AssemblyTools Required Phillips screwdriver Torque wrench 3/16” Allen wrench (supplied) 7/32” Allen wrench (supplied) (2) 9/16” Open-end wrenchNOTE: The words “left” and “right” denote the user’s orientation.1. Read and understand all instructions thoroughly before assembling unit.2. Verify correct package.A. Read box label to verify the model number and voltage (optional) match what was ordered.B. Lift and remove cardboard sleeve surrounding unit.C. Verify paint color matches what was ordered.D. Verify correct voltage if option AC power kit is included.3. Unpack and verify 750A contents of carton.NOTE: For 750AT content verification, skip to step 5.A. See 750A content listing and Figure 1a for 750A carton contents.B. Check off each item as found. See Customer Service – Chapter 5 for contact information if anyparts are missing.750A ContentsItem12a2b345678910Qty11121111111Assembly and Set UpPage 2-2Part 1NA5750-4750A-402750A-391750A-392DescriptionBase with covers attachedConsole assembly (in box)Handrail assemblyFoot padTray, MainTray, InsertHardware packOwner’s ManualAssembly posterCommercial Arc warranty sheetConsumer Arc warranty sheet

Cybex Arc Trainer 750A/750AT Owner’s Manual2b2a7196108543Figure 1a (750A)4. Verify contents of 750A hardware pack.A. See 750A hardware pack listings and Figure 1b for 750A hardware pack contents.B. Check off each item as found. See Customer Service – Chapter 5 for contact information if anyparts are missing.Assembly and Set UpPage 2-3

Cybex Arc Trainer 750A/750AT Owner’s Manual750A Hardware PackItem11121314a14b14c14d1516Qty445211411Part 0428HX700412BK030204YA000201DescriptionTap SC 10-12 x 2.00 Type A PN HD PHILLocknut, .375-16 NylonBHSCS .375-16 x 2.25Pan HD Phil Hd Self Tapping, 8-16 x .50 Type WBWasher, Saddle, .390 ID x .750 OD x 6BHSCS .375-16 x 2.25 SSBHSCS .375-16 x .50 SS7/32” Allen 3414c14d14b14c14d11516Figure 1b (750A)Assembly and Set UpPage 2-43

Cybex